Legendary RS power for micro FPV racing quadcopters available in 7500, 6000 and 4500 KV
The new RS1106 brushless motor line sets a new standard in performance for the 2” propeller class. With 3 KV choices each optimized for 2s, 3s and even 4s batteries for insane speed in tiny package.
The RS1106 has 6mm tall stator to provide the instantaneous torque that is usually lacking in high KV 1104 motors. The RS1106 is also one of the only micro brushless motors with active cooling fins integrated into the bell to keep magnets cooler so the power is consistent lap after lap.
For micro builds it’s important to have as little mechanical vibration to get the best performance from your flight controller. To ensure smoothness each motor is precision CNC, uses premium ball bearings and comes factory balanced.
The bell housing has two sizes of hole spacing to fit the EMAX 2345 Tri-Blade and M2 x 5mm that works with a wide range of other 2” class propellers. Two lengths of mounting screws are included for so it will fit a wide range of frame styles.
RS1106 7500KV is the perfect upgrade for those stepping up from 1104 size that typically come with many 2s ready to fly builds.
RS1106 6000KV is a versatile upgrade motor for 2s-3s and well suited for those wishing to spin heavier 4 blade or 5 blade propellers.
RS1106 4500KV this the motor if want insane punch with efficiency when using 4s batteries. This motor can also spin lightweight 3” propellers up 3s
1.Most powerful micro motors for 2” to 3” propellers
2.RS exclusive “Cooling” design on a micro sized motor
3. 3 KV options 4500KV, 6000KV, 7500KV
4. Prop bolt pattern for Emax 2345 M2 x 9mm and M2 x 5mm Propellers
5.High Quality NSK bearings for long lasting smoothness
6. Strong N52SH Magnets
7. Factory Balanced Precision CNC Motor Bells
Posted by shatiff on Mar 29th 2018
these motors are strong and fast to be so small .. they can take a serious hit while flying.. one of the best for your two or three inch quad.. i would recomend these to any micro flyer out there... be very careful with mounting screw size, as you will kill your motor if they are too long..
Posted by Calipr on Oct 11th 2017
Great shipping from EMAX USA. Shipped same day as ordered and they arrived 2 days later with standard shipping (CA->FL). The 1106 are really small compared their 1306 bigger brother. Not installed yet but I must say they look really good and I like the silicone wires. The extra sets of mounting screws is also a welcome addition. You get 5 M2 screws each at lengths of 3, 4, 5mm plus 4 M2 at 6mm for props. They could probably skip the 3mm set because I'm not sure if they would ever be used on a typical quad frame, maybe a 1 mm plate for a different application? I would prefer a 7-8mm set because with a 3mm frame and two 1-1.5mm soft mounts this just fits on my typical microquad.
Posted by email@example.com on Sep 21st 2017
These motors are great! Well balanced and the fit and finish is perfect! Beware they are very powerful and fast.
Posted by Erik Waluska on Sep 18th 2017
I've been using the emax babyhawk 1104 5800kv motors and props on a Marvin 113 micro quad for a few months and they are very good motors but can't really handle 3S because they get too hot and burned out the bearings on three of them. I replaced those bad motors and have only run 2S batteries on them since and the motors stay cool and the quad flies great and has decent power. But dang the power on 3S was haunting me so I was anxious to try these new little red bottoms and I am not disappointed. Since I wanted power AND reliability I went with the 1106 4500kv motors, which are supposed to have about the same thrust as the babyhawk motors on 2S but nearly twice the thrust on 3S. Tested them yesterday and these motors totally rock! Power on 2S was similar to the babyhawk motors but for some reason hovering required about 60% throttle, however the upper end of the power range seemed stronger and the motors came down cool as a cucumber. The power on 3S is awesome! Super smooth and pretty quiet too - until you punch it, then they scream. After a pretty aggressive flight the motors were barely warm to the touch so I expect these to last a long time! I'm so glad emax made these accept the babyhawk props and also other brands as well. Looking forward to experimenting with different props. Love these motors!!
Posted by Baddy on Sep 6th 2017
I have been waiting for these motors for some time now! SUPER excited to have a micro motor from the best dang motor company in FPV! (arguably, of course. No, I didn't get sponsored to say that)
High quality, superb power, smooth operations....."Flawless Victory"!
If you're looking for a quality motor that will turn heavy props on a heavy micro (120g ish), these are the motors for you!
Thank you Emax - my hero!